Conversion Kits
*Shipping will be quoted after checkout
FirstLight Voile Kit *
A$
360.00
This kit will transform your old Burton board with Burton interface into a new board!! The kit now allows you to have a board with the Voile hardware.The kit includes all parts need to get straight on the mountain.Slider plates and all screws included. The kit comes with instructions and there is a small video too if needed. See some of the boards modified here.
FirstLight Voile Kit for Spark or Light Rail *
A$
310.00
This kit will transform your old Burton board with Burton interface into a new board!! The kit now allows you to have a board with the Voile hardware.The kit includes all parts need to get straight on the mountain.Slider plates and all screws included. The kit comes with instructions and there is a small video too if needed. See some of the boards modified here.
FirstLight Kit Old *
A$
200.00
This is a smaller version of the Burton to Voile kit. All parts supplied are made by FirstLight Snowboards. You can buy the other Voile Parts from the Voile Website if needed.
This kit suits the old Voile climbing bars.
Screws included
See some of the boards modified here.
This kit suits the old Voile climbing bars.
Screws included
See some of the boards modified here.
FirstLight Kit New *
A$
210.00
This is a smaller version of the Burton to Voile kit. All parts supplied are made by FirstLight Snowboards. You can buy the other Voile Parts from the Voile Website if needed.
This kit suits the New Voile climbing bars.
Screws included
See some of the boards modified here.
This kit suits the New Voile climbing bars.
Screws included
See some of the boards modified here.
FirstLight Slider Plates *
A$
80.00
5 deg Canted FirstLight Slider Plate *
A$
40.00
Voile compatible puck with 5 degrees of cant.
Great for hard booters rear foot!
Voile plate and Light Rail compatible.
Shim required for use with Spark binding, please ask.
Great for hard booters rear foot!
Voile plate and Light Rail compatible.
Shim required for use with Spark binding, please ask.
2.5 deg Canted FirstLight Slider Plate *
A$
40.00
Voile compatible puck with 2.5 degrees of cant.
Great for hard booters rear foot!
Voile plate and Light Rail compatible.
Shim required for use with Spark binding, please ask.
Great for hard booters rear foot!
Voile plate and Light Rail compatible.
Shim required for use with Spark binding, please ask.
Burton to Voile converter toe plate *
A$
65.00
This plate will convert the old Burton stud pattern to suit the Voile toe hardware. Sold as a pair. See some of the boards modified here.
Burton to Voile converter Old Heal Plate *
A$
55.00
This plate will convert the old Burton stud pattern to suit the old Voile heal hardware. Sold as a pair. See some of the boards modified here.
Burton to Voile converter New Heal Plate *
A$
60.00
This plate will convert the old Burton stud pattern to suit the new single and dual Voile heal hardware. Sold as a pair. See some of the boards modified here.
Splitboard pin Spark R&D LT Pin system
A$
25.00
Use this when in board mode to stop the two half of the board flexing or twisting.
All we need to know is the distance from the outside of the toe attachments.
See some examples
All we need to know is the distance from the outside of the toe attachments.
See some examples
Splitboard pin Voile touring hardware
A$
25.00
Use this when in board mode to stop the two half of the board flexing or twisting.
All we need to know is the distance from the outside of the toe attachments.
See some examples
All we need to know is the distance from the outside of the toe attachments.
See some examples
Splitboard pin Karakoram touring hardware
A$
30.00
Use this when in board mode to stop the two half of the board flexing or twisting.
All we need to know is the distance from the outside of the toe attachments.
See some examples
All we need to know is the distance from the outside of the toe attachments.
See some examples
Voile Slider Track *
A$
32.00
Your binding attaches to the Slider Track using binding screws and T-nuts. The Slider Track is utilized in ride and tour mode and is attached to the splitboard with (price is for one).
Voile Slider Track Gaskets - Pair *
A$
12.00
The Slider Track gasket is sandwiched between your binding and the aluminum
slider track. This will add dampening to the ride and also help take up any
extra binding screw length and prevent that extra screw length from protruding
past the T-nut and further preventing the Slider Track from easily sliding on
Universal Puck system.
Voile Slider Pin *
A$
22.00
The Slider Pin secures the Slider Track to the splitboard in tour and ride
modes. The stainless steel cable lanyard is attached to your binding to prevent
the pin from being lost in the backcountry. It is also advisable to carry a
spare. (Price is for one)
Split Hooks *
A$
35.00
Set of 4 Hooks. Includes all screws, bushings, nuts, and drill template to mount
to a cut-your-own splitboard.
Karakoram Board Clips
A$
50.00
The Karakoram Board Clips match the factory splitboard hole pattern and efficiently join the two halves of your splitboard for a slop-free ride mode.
Note:
This set does not include mounting screws or nuts. If your splitboard has the Voile Hook interface, you can reuse the Voile screws and nuts
Note:
This set does not include mounting screws or nuts. If your splitboard has the Voile Hook interface, you can reuse the Voile screws and nuts
Voile Split Kit Pucks (4) Split-your-own-board *
A$
27.00
The new Voile Split Kit Puck with 2-hole secure t-nut mounting. The pucks hold
the Slider Track in place and provide the bridge for the 2 splitboard halves.
Includes 8 M6 x 12mm truss-head screws, 8 M6 round bottom t-nuts, and 8 Petex
discs to mount to board half. You will need to have a split kit puck sticker
template to determine mounting position for your proper angles and stance width.
Voile Tip Clips *
A$
19.00
One pair of tough nylon tip-clips and all rivets and bushings to repair or
replace old worn-out or broken tip-clips. Take care when drilling out rivets to
remove old tip clips, so as not to enlarge hole and make the tip-clip have a
sloppy fit. Tip: The "bulleted" end of the Slider Pin will act as roll-over tool
for the rivets of the tip-clips. Holding the head of the rivet securely, use a
smaller hammer and the Slider Pin to roll the back of the rivet over and secure
the tip-clip to the board.
Voile Touring Bracket *
A$
42.00
Stainless steel bracket where the Slider Track attaches during the tour
mode. Attached with stainless steel Slider Pin. Touring Bracket includes
the plastic pin guide and all screws necessary to mount.
LT Pin System *
A$
99.00
A new touring bracket and pin
combination for splitboarders, looking for better performance and
durability. The LT Pin System is stiffer, lighter and slop free, for a
more efficient tour.
Self-lubricating plastic bushings within the touring bracket drastically reduce wear and allow the use of 7075 aluminum pins
Aluminum pins are half the weight of standard Spark pins, shaving 3.5oz/100g off the setup.
Self-lubricating plastic bushings within the touring bracket drastically reduce wear and allow the use of 7075 aluminum pins
Aluminum pins are half the weight of standard Spark pins, shaving 3.5oz/100g off the setup.
Voile splitboard dual height climbing heels *
A$
49.00
Upgrade your splitboard with the new Voile splitboard dual height climbing
heels. The back climbing wire is the standard height of 55mm and the front wire
is 75mm. Also new, a durable plastic coating is applied to the top of
each wire to prevent wear on your splitboard binding base plate.
Includes 1 pair of dual height climbing heels/wires and screws to mount
to an inserted, factory-built splitboard.
Voile SD Tall Climbing Wire *
A$
14.00
1 pair of 72mm climbing wires to increase efficiency in tour mode.
Dual Height Climbing Wires *
A$
56.00
8mm Base climbing heels with dual height climbing wires easily activate and stow to reduce fatigue and increase traction during steep ascents.
55mm and 75mm climbing wires included.
These are compatible with Voile hole pattern.
55mm and 75mm climbing wires included.
These are compatible with Voile hole pattern.
Voile Splitboard Touring Riser
A$
24.00
Increase your uphill touring rotation and enhance your edging ability while
side-hilling with the new Voile Splitboard Touring Riser.
This 10mm riser, especially with larger boots, increases the rotational angle of your binding and prevents the boot toe from hitting the deck of your board.
It will also give you more leverage and boot/binding angulation to enhance your edging ability on steep sidehills.
This 10mm riser, especially with larger boots, increases the rotational angle of your binding and prevents the boot toe from hitting the deck of your board.
It will also give you more leverage and boot/binding angulation to enhance your edging ability on steep sidehills.
Voile Split Kit- (DIY)cut-your-old-board kit *
A$
180.00
This is the cut-your-old-board kit. The Voile Split Kit includes all hardware
and step-by-step instructions to split your old board.
Voile Universal Splitboard Hardware *
A$
115.00
Attention! Please Read! This
hardware kit is for factory-built splitboards that have inserts. It is
NOT for Sawing Your Old Board (Split Kit - DIY).
Got a new splitboard and it's not a Voile?
This is the rest of hardware you need to get on the snow.
Don't forget Voile Splitboard Climbing skins.
Works with these brands
Burton Snowboards, Unity Snowboards,Jones Snowboards, Venture Snowboards, K2 Snowboards, Voile Splitboards, Voile Snowboards, Winterstick Snowboards, Never Summer Snowboards, Prior Snowboards and Spark R&D bindings
Got a new splitboard and it's not a Voile?
This is the rest of hardware you need to get on the snow.
Don't forget Voile Splitboard Climbing skins.
Works with these brands
Burton Snowboards, Unity Snowboards,Jones Snowboards, Venture Snowboards, K2 Snowboards, Voile Splitboards, Voile Snowboards, Winterstick Snowboards, Never Summer Snowboards, Prior Snowboards and Spark R&D bindings
White Wave Traction kit *
A$
260.00
Surf the mountain on any splitboard you already have. Redraw lines of seasons past. Familiar terrain has an entirely new feel. Your mountain canvas is blank, how will your mark?
The white Wave Traction setup is your backcountry quiver killer. Transition from snowboard to splitboard and from traction pad to binding all in tha matter of minutes. No adhesive attachment means your board is only as committed as you want it to be. See some of the boards modified here.
The white Wave Traction setup is your backcountry quiver killer. Transition from snowboard to splitboard and from traction pad to binding all in tha matter of minutes. No adhesive attachment means your board is only as committed as you want it to be. See some of the boards modified here.
FirstLight NoBoard Kit *
A$
105.00
Want to ride the Freshies like the old days?
Stick one of kits on and hang on for the ride.
Kit comes with deck grip and a bungie strap , all that's needed to get straight out there!
Optional Leg Rope for sale if needed?
See some of the boards modified here.
Stick one of kits on and hang on for the ride.
Kit comes with deck grip and a bungie strap , all that's needed to get straight out there!
Optional Leg Rope for sale if needed?
See some of the boards modified here.
* Shipping will be quoted after checkout. For a quote in advance contact us
Ph: +61 (0)413 888 115
Ph: +61 (0)413 888 115
